Sie haben keine Artikel im Warenkorb.
Yes it can! And this was achieved by using 4 main changes in design
1. First of all, the Ortur LM3 was redesigned to have its mechanical structure center of gravity as low as possible. Ultimately, there is a substantial reduction in the frame harmonic vibrations.
2. Secondly, the LU2-10A 10W laser module that powers the Ortur LM3 is extremely light. Only 235 grams, maintaining high power delivery and cooling performance.
3. The Ortur LM3 motherboard and firmware employs G-code streaming optimization, allowing the transfer of data to break the old limitations of 6,000mm/min.
4. TMC2209 stepper driver chips are used on the Ortur LM3. These high performing drivers allow for high torque, silent operation and no switching homing.
Ultimately it will save time. In combination with the 10w true optical power of the LU2-10A, the Ortur LM3 can double the work output possible with a Laser Engraver. If you're using an laser engraver on a commercial say, you will be able to serve twice as many customers in the same amount of time. Time become actual Money!
As an example, it takes 30 minutes to engrave a black and white image of about 10CMx10CM at a speed of 6000mm/min. The same image engraved at max speed with the Ortur LM3 can be finished in roughly 10 minutes.
The true figures of speed must be calculated when considering speed settings but also the acceleration settings used on the machine firmware. Many machines allow 10,000mm/min to be used, however their acceleration figures are so conservative that the exact actual measured speed when engraving will not surpass real 6000mm/min. The real test has to be done with a watch and a true time metering of time per 10cm2.
The same is often employed on metering power values on Laser Modules. The important figure is the optical output at 100% power, and not the electrical input value used by the module. Where others claim 80, 90, 130W we present our true optical value of power output.
After Sales Points in Portugal，Western America.
If you cut more, you can choose the LF version, it better in cutting, and the black edge will not be obvious.
The main difference comes in "ease of use" and Options. Regular engraving machine tend to have the basic functionality, connect via USB and need a computer software to be operated. Although this is perfectly fine, many times alternative work flow options are necessary.
Our LM3 smart engraving machine solves the problem by offering 5 machines in one. Users can still operate normally from USB, use a Phone App, Upload Gcode Via FTP, and more importantly have a full WebUi interface to change and alter all aspects of the machine. From starting engraving to update and change firmware settings.
The more important aspect we tried to address with the Ortur LM3 is the different skill levels users tend to have when using their first Laser Engraver. Also their goals.
Some users want to do simple engravings, without multiple layers and complexity. Up to now these users were forced to learn complex and limited software.
Now users can simply use their phone, take a picture, or write text and start engraving in minutes. For those that want to use their machine at 100%, all the other options remain available. No compromises required!
Not Every engraving job requires a computer and complex software. Many of our loyal users do on the fly customization for their customers. This can make the Ortur LM3 a prime portable machine to use on fairs and events. All needed is the Laser Explorer, and an compatible Android or iOS phone. From the simplest to the more complex jobs, all can be done at the touch of a phone screen.
Time evolved, and the power of the integrated chips did too. Currently the Ortur LM3 is powered by the ESP-Pro-v2.4 motherboard. Powered by a ESP32 chip and a lot of Extended I/O, a reinforced power delivery system and the TMC 2209 Silent Stepper drivers for all 3 axis. This is the eleventh generation motherboard released by Ortur Laser Application Technology Laboratory, with a very mature and solid design.
On top of the hardware, our Latest 2.0 firmware support the latest IoT technology, allowing better laser engraving protocol standards, image direct engraving, WebUI, multi-language interface, integrated system detection mode, and many other advanced features.
With the latest TMC 2209 stepper driver chips, there is no longer the need of physical limit switches to have consistent and perfect homing operations. On top of that, the operation of the machine will near silent at low speeds and very quiet at maximum speeds.
The latest ESP-Pro-v2.4 motherboard is designed to have bi-directional I/O interfaces. Not only the motherboard will talk to the machine components, but these can also communicate and report back to the motherboard on their current state. Soon expansion I/O products will be released to give the machine even the power to control the environment around the Ortur LM3.
Commonly, laser engravers would use USB Serial port communication. This would require a permanent USB wire connection to a host computer. With the Ortur LM3, this will be available but be only one of 5 options. The machine will give the ability to engrave from USB, SD card, WebUi, FTP, and App. The machine can connect to your wifi network, or provide itself a WIFI network to be connected to (Access Point mode).
Compared with the older generation of laser engraving protocol standards, it is 5 times more efficient.
Using AI, the Ortur LM3 Firmware will be able to convert and optimize a image directly sent to the machine and generate automatically gcode without user intervention, cumbersome settings or parameters.
Your Ortur LM3 will be a machine and a service. A webserver is built in your machine firmware and you will be able to connect to your machine via a standard browser. On your Computer, Chromebook, Laptop, Ipad etc. Any device that has the ability to launch a browser and is connected to your network will be a point of control.
Simply put, with the recent increase in power on Laser modules, the engraving machines are no longer a toy. They are dangerous machines that need to be respected. Having a machine designed with safety first in mind is a important aspect Ortur pursued.
a) Emergency switch - One press and the whole machine will stop ALL operations.
b) Safety Lock – A Key will lock or unlock the machine. Without this key no operations will be possible.
c) Movement Detection – Pan, Tilt, Shock and Position sensors will stop the machine if an abnormal motion of the machine Is detected.
d) Laser Exposure and Duration Detection – If the firmware detects that the Gcode sent to it will have the machine use too much power without being moved, it will immediately stop the laser beam and issue an alert.
e) Voltage & Current Monitoring – The Ortur LM3 can read, monitor and detect any abnormal behavior of the power delivery system. Drop on voltage of excess power requirements from the machine components will result in a machine halt to keep the components safe.
f) Connection detection- A laser engraver cannot lose connection to its host streaming channel. If the connection to the host computer/Device is lost the machine will halt operations.
a) High-precision structural parts processed by CNC are required to ensure structural accuracy.
b) High subdivision motor driver IC is required.
c) Requires a 16-tooth synchrotron wheel that is smaller than the diameter of a normal 20-tooth sprocket.
d) Requires a closed-loop belt e)Needs to optimize the motion parameters in the firmware, especially the relationship between the weight and acceleration of the laser module.
f) Requires an ultra-fine laser spot brought about by the fourth generation of compression technology
In the engraving, it can ensure that the gray level of the photo is highly maintained, and ensure that the line drawing is accurately portrayed. During the cutting process, precise cutting at the 0.1mm level is ensured.
There is no need to remove the connections of the Y-axis motor to insert the YRR 2.0 Rotary Roller, and with a single stroke, you can make a conversion between the YRR 2.0 Rotary Roller and the Y-axis motor.
Lower the focus bar to focus, lower the laser module to it touches the material. Fold the focus bar back and its ready to start engraving.
As soon as the air tube is inserted into the laser module, it is used. All that’s required is an air source.
Optional I/O Components that expand the machine functionality will be added in future.
Ortur Laser Engraving Platform can provide suspension support, smoke conduction and fixation for the carving, avoiding the smoke accumulation of smoked yellow carved objects during the use of ordinary honeycomb boards.
With a Z stroke of 50mm, it can be combined with the XY axis to achieve depth and surface engraving, and even thicker material cutting.
Made of fireproof cloth and fireproof plastic, it is easy to fold and provides a closed environment for the engraving machine.
Extend the Y-axis travel to 800MMx400MM
We do accept paypal, credit card, and bank transfer.
Our default currency setting is USD, customers paying in other currencies will be automatically converted according to the exchange rate.
Yes, contact Support@ortur.net for a quote.
Yes, contact firstname.lastname@example.org and provide your social media link for us to review.
We will ship from US, CZ, CN warehouse depend on customer location and stock availbility.
For most of countries , we provide free shipping, but some remote areas, including islands, etc.,free shipping is not provided. Buyers need to pay part of the shipping fee.
Currently, do not offer home delivery service.
1.Track your order status on website
2.Contact Support@ortur.net for more details
Laser Engraver: 12 months
Accessories: 6 months
Very welcome to extend warranty period. However, since different customer places the order in different time, the fee of extending warranty is also different. If you want to know details, please contact our customer service manager for specific details: email@example.com
We have a 30-day return policy, which means you have 30 days after receiving your item to request a return.
To be eligible for a return, your item must be in the same condition that you received it, unworn or unused, with tags, and in its original packaging.
To start a return, you can contact us at Support@ortur.net and send picture of product condition. If your return is accepted, we’ll send you a return shipping label, as well as instructions on how and where to send your package. Items sent back to us without first requesting a return will not be accepted.
Sorry for that situation, due to the complexity of the damaged parts, we need to check out the specific damage situation. Please contact our after-sales service team for alternative plan: firstname.lastname@example.org.
As we understand, you are having technical issues with our machine, we have a 24/7 team of customer support that would quickly address the problem.
Please visit our ticketing system at https://ortur.tech/support or email us at email@example.com.
A reply will be promptly sent