Specific parameters of the winning works – Ortur
          

Join Ortur Family

Join the group to get the latest news & winners of the event, the engraving parameters of the winning works and solve the technical problems you encounter

Join Ortur Family

Join the group to get the latest news & winners of the event, the engraving parameters of the winning works
and solve the technical problems you encounter

Winners of April

Winners of April

Winner:Nickolas***

I made a set of 4 coasters , 4 placemats and a serving board with elephant theme for a customer, all om slate.
I processed the images using Imag-r and then put it through lightburn.
With the following settings:
Speed: 2800mm/s; Power: 80%;
DPI: was set at 318 in Imag-r and then passthrough used in Lightburn;
Coaster size: 100mm x 100mm;
Placemat size: 300mm x 200mm;
Serving board size: 500mm x 250mm.

Winner:Nickolas***

Specific parameters:

I made a set of 4 coasters , 4 placemats and a serving board with elephant theme for a customer, all om slate.
I processed the images using Imag-r and then put it through lightburn.
With the following settings:
Speed: 2800mm/s; Power: 80%;
DPI: was set at 318 in Imag-r and then passthrough used in Lightburn;
Coaster size: 100mm x 100mm;
Placemat size: 300mm x 200mm;
Serving board size: 500mm x 250mm.

Winner:TECH***

Inverting the image to create a negative;
Side inversion left to right;
1 layer, cutting speed 1000, power 100%, number of passes 8, dpi 96DPI;
2 layers enlarged by 1mm, cutting speed 1000, power 100%, number of passes 8, dpi 96DPI;
3 layers enlarged by 1mm, cutting speed 1000, power 100%, number of passes 8, dpi 96DPI
Air assist 10l / min material;
Mirror 8mm made in IKEA.

Winner:TECH***

Specific parameters:

Inverting the image to create a negative;
Side inversion left to right;
1 layer, cutting speed 1000, power 100%, number of passes 8, dpi 96DPI;
2 layers enlarged by 1mm, cutting speed 1000, power 100%, number of passes 8, dpi 96DPI;
3 layers enlarged by 1mm, cutting speed 1000, power 100%, number of passes 8, dpi 96DPI
Air assist 10l / min material;
Mirror 8mm made in IKEA.

Winner:mount***

Tools used:
Ortur Laser master 2 pro
Settings used:
Line 500/85/5
Fill 2000/80
Line 700/60

Winner:mount***

Specific parameters:

Tools used:
Ortur LM2 Pro
Settings used:
Line 500/85/5
Fill 2000/80
Line 700/60

Winner:lites***

LM2 Pro S2 with LU2-4 Module
A total of about 52 different pieces went into making this
Overall length is about 20 inches, so it was done in two sections
Materials used include:
1/16" Beech plywood
1/8" Baltic Birch plywood
1/4" Poplar solid (for main body and neck of guitar)

Winner:lites***

Specific parameters:

LM2 Pro S2 with LU2-4 Module
A total of about 52 different pieces went into making this
Overall length is about 20 inches, so it was done in two sections
Materials used include:
1/16" Beech plywood
1/8" Baltic Birch plywood
1/4" Poplar solid (for main body and neck of guitar)

Winner:Erik Abr***

Made with LM2-Pro LF 20W
Glass Shadow Box Frame Painted black
Engraved painted side with following settings:
Norton glass
10000 mm/m
60% Max Power
0% Min Power
318 DPI

Past winning works

Winner:Erik Abr***

Specific parameters:

Made with LM2-Pro LF 20W
Glass Shadow Box Frame Painted black
Engraved painted side with following settings:
Norton glass
10000 mm/m
60% Max Power
0% Min Power
318 DPI

Past winning works

Winner:Martin***

Burn speed/power 200/80%, 1 pass,
LightBurn sofrware, air assist, improved Laser master 2 with 400x800 mm burn area, fix fokus and materiál is Cardboard 3mm.
The individual layers were fired and then glued together.

Winner:Leathercraft***

Ortur Laser Master 2 Pro S2 LU2-4-SF
Pattern and image processed in Lightburn
Settings:
Image: 4000mm/min, 52.5% power
Stitching holes: 175mm/min, 60% power, 2 passes
Cutting: 200mm/min, 60% power, 2 passes

Winner:Kelly ***

Ortur Laser Master 2 

Winner:Leathercraft ***

Ortur Laser Master2 Pro S2 with LU2-4 SF module
3 oz vegetable tanned leather for the wallets and 6 oz vegetable tanned leather for the keychains.
Engraving: 3900mm/min, 50% power
Cutting: 175mm/min, 60% power(2 passes for the 6 oz leather)

Winner:Tom ***

Something a bit different: Leather juggling balls.
Engraving and cutting (also cutting the stitching holes) done with laser. Stitching done by hand. In the inside is a balloon filled with millet seed to give the balls a uniform weight.
 Tools used: Ortur Laser Master 2Pro S2 with LU2-4 SF 2 needles for stitching the leather parts together
Materials: Vegetable tanned leather, 5oz(2mm)thickness 1mm Leather thread Balloons filled with red millet seeds
Settings used:
For engraving: JPG image, 400DPI, 4000mm/min, 45% power
For cutting the outer shape: 175mm/min, 65% power, 2 passes(3 passes for the red leather)
For cutting the stitching holes: 300mm/min, 60% power, 2 passes(3 passes for the red leather)

Winner:Martin ***

I send you a picture of Hurdy Gurdy which I finished in November. Burn speed/ power 200/80%, LightBurn sofrware, air assist, improved Laser Master 2 with 400x800mm burn area.

Winner:Dave***

Ortur Laser Master 2 Pro
500mm/min, 85% power, 5 passes, 3mm

Ortur Laser Master 2 Pro
750mm/min, 90% power, 7 passes, 8 Layers 

Ortur Laser Master 2 Pro
900mm/min, 95% power, 8 passes, 3mm Basswood, 9 layers 

Winner:Mikk ***

ORTUR Laser Master 2 20W - SF 5.5W
Corel Photopaint for pre-processing.
Set 318dpi, and increase Brightness and Contrast.
Lightburn for laser control.
 Speed : 1400mm/min, Power : 75%,
Resolution : 318dpi, Scan Angle : 0°,
Dithering mode : Dither,
White acrylic paint on ceramic tile - 200mm x200mm
Burn time : 2hr 11 minute - 1 Pass.
Washed with water under the tap to remove small amount of residual soot.

Winner:Karl***

Vintage map on slate board.
3000 80 @.13. Followed up with clear spray can to give shine.
The slate board was terribly uneven.
I used shims to bring up the one side 1/4 inch.

Winner:Customized***

What i made was a 2 layer design one of 3mm poplar plywood painted red and a top layer of 2 mm oak. Settings of the first one are 200 speed & 80 % power with 2 passes ,no dpi settings. On the back i made my logo, Settings of that are 2000 Speed and 50% power dpi 274, one pass. The Top layer is the 2 mm oak. Settings for this layer are 200 speed and 80% Power and 2 passes. I glued the 2 layer together

Winner:David***

Baltic Birch 2000/45/318/90 Borax mix and white wash Stucki Lightburn 

Winner:Simon***

Ortur Laser Master 2 with upgraded 12v pro laser module.
Engrave: 1700 / 40%
Cut: 260mm/min, 85% power, 4 passes

Ortur Laser Master 2 with upgraded 12v Pro laser module (would be a dream to win a pro!)
Cutting: 260mm/min, 85% power, 4 passes

Ortur Laser Master 2 with upgraded 12v Pro laser module (would be a dream to win a pro!)
Engraving: 800mm/min, 95% power, 4 passes

Ortur Laser Master 2 with upgraded 12v Pro laser module (would be a dream to win a pro!)
Cutting: 260mm/min, 85% power, 4 passes

Ortur Laser Master 2 with upgraded 12v Pro laser module (would be a dream to win a pro!)
Engraving: 1700mm/min, 40% power for wood,  6000mm/min, 80% power for slate

Winner:neilv***

Rustoleum Flat grey Primer LU2-4 400mm/min, 95% power

Winner:Leathercraft***

Specific parameters:

Ortur LM2 Pro S2 LU2-4-SF
Pattern and image processed in Lightburn
Settings:
Image: Speed 4000mm/min, 52.5% power
Stitching holes: Speed 175mm/min,  60% power, 2 passes
Cutting: Speed 200mm/min, 60% power, 2 passes

Winner:Martin***

Specific parameters:

Burn speed/power 200/80%, 1 pass, LightBurn sofrware, air assist, improved LM2 with 400x800 mm burn area, fix fokus and materiál is Cardboard 3mm.
The individual layers were fired and then glued together.

Winner:Kelly ***

Ortur LM2 

Winner:Martin***

I send you a picture of Hurdy Gurdy which I finished in November.
Burn speed/ power 200/80%, LightBurn sofrware, air assist, improved LM2 with 400x800mm burn area.

Winner:Tom ***

Something a bit different: Leather juggling balls.
Engraving and cutting (also cutting the stitching holes) done with laser. Stitching done by hand.
In the inside is a balloon filled with millet seed to give the balls a uniform weight.

Tools used:
Ortur LM2 Pro S2 with LU2-4 SF
2 needles for stitching the leather parts together
Materials:
Vegetable tanned leather, 5oz(2mm)thickness
1mm Leather thread
Balloons filled with red millet seeds
Settings used:
For engraving: JPG image, 400DPI, 4000mm/min, 45% power
For cutting the outer shape: 175mm/min, 65% power, 2 passes(3 passes for the red leather)
For cutting the stitching holes: 300mm/min, 60% power, 2 passes(3 passes for the red leather)

Winner:Leathercraft***

Specific parameters:

Ortur LM2 Pro S2 with LU2-4 SF module
3 oz vegetable tanned leather for the wallets and 6 oz vegetable tanned leather for the keychains.
Engraving: 3900mm/min, 50% power
Cutting: 175mm/min, 60% power(2 passes for the 6 oz leather)

Winner:Dave***

Specific parameters:

①Ortur LM2 Pro-500mm/min, 85% power, 5 passes, 3mm

②Ortur LM2 Pro-750mm/min, 90% power, 7 passes, 8 Layers 

③Ortur LM2 Pro-900mm/min, 95% power, 8 passes, 3mm Basswood, 9 layers 

Winner:Mikk ***

Specific parameters:

ORTUR LM2 20W - SF 5.5W
Corel Photopaint for pre-processing.
Set 318dpi, and increase Brightness and Contrast.
Lightburn for laser control.
Speed : 1400mm/min,
Power : 75%,
Resolution : 318dpi,
Scan Angle : 0°,
Dithering mode : Dither,
White acrylic paint on ceramic tile - 200mm x200mm
Burn time : 2hr 11 minute - 1 Pass.
Washed with water under the tap to remove small amount of residual soot.

Winner:Karl***

Vintage map on slate board. 3000 80 @.13.
Followed up with clear spray can to give shine.
The slate board was terribly uneven.
I used shims to bring up the one side 1/4 inch.

Winner:Customized***

Specific parameters:

What i made was a 2 layer design one of 3mm poplar plywood painted red and a top layer of 2 mm oak. Settings of the first one are 200 speed & 80 % power with 2 passes, no dpi settings. On the back i made my logo, Settings of that are 2000 Speed and 50% power dpi 274, one pass. The Top layer is the 2mm oak. Settings for this layer are 200 speed and 80% Power and 2 passes. I glued the 2 layer together

Winner:David***

Specific parameters:

Baltic Birch 2000/45/318/90 Borax mix and white wash Stucki Lightburn 

Winner:Simon***

Specific parameters:

①Ortur LM2 with upgraded 12v pro laser module. Engrave: 1700 / 40% Cut: 260mm/min, 85% power, 4 passes;

②Ortur LM2 with upgraded 12v Pro laser module (would be a dream to win a pro!) Cutting: 260mm/min, 85%  power, 4 passes;

③Ortur LM2 with upgraded 12v Pro laser module (would be a dream to win a pro!) Engraving: 800mm/min, 95% power, 4 passes;

④Ortur LM2 with upgraded 12v Pro laser module (would be a dream to win a pro!) Cutting: 260mm/min, 85%  power, 4 passes;

⑤Ortur LM2 with upgraded 12v Pro laser module (would be a dream to win a pro!) Engraving: 1700mm/min, 40% power for wood, 6000mm/min, 80% power for slate.  

Winner:neilv***

Specific parameters:

Rustoleum Flat grey Primer LU2-4 400mm/min, 95% power

        
BACK TO TOP